当前位置: 首页 > 产品 > 无线解决方案 > IAP-6002WA
IAP-6002WA

Industrial 802.11 a/b/g Redundant Access Point

  
 
 Overview
     IAP-6002-WA/WA+ is a reliable 802.11a/b/g WLAN with 2 ports LAN Access Point. It supports LLDP for topology discovery and STP for wireless/wired redundant connections. It also supports 802.1X and MAC fi lter for security control. It can be confi gured to operate in AP / Bridge / Repeater / AP-Client mode. You are able to confi gure IAP-6002-WA/WA+ by WEB interface via LAN port or WLAN interface. IAP-6002-WA/WA+ provides dual Ethernet ports in switch mode, so that you can use Daisy Chain to reduce the usage of Ethernet switch ports. In addition, IAP-6002-WA+ also provides PD feature on ETH2 which is fully compliant with IEEE802.3af P.O.E. PD specifi cation. Therefore, IAP-6002-WA/WA+ are one of the best communication solutions for wireless applications on the industrial network.

 产品特征
• WLAN interface support up to 54Mbps link speed
• Various kinds of operation modes supported: AP/ Bridge/Repeater/AP-Client mode
• Various kinds of encryption supported: WEP/WPA/ WPA-PSK(TKIP,AES)/WPA2/ WPA2-PSK(TKIP,AES)/802.1X Authentication
• Dual redundant Ethernet port support redundant mode (Recovery time < 10ms)
• Ethernet switch mode enable Daisy Chain
• Wireless connecting status monitoring
• Versatile modes & event alarm by e-mail
• HTTPs protocol supported for secured management
• IP table to prevent access from unauthorized IP address
• IP Confi gurable by Windows utility (AP-Tool)
• 1KV isolation for PoE PD port of IAP-6002-WA+
• Dual redundant DC power inputs of terminal block
• Rigid IP-30 housing design
• DIN-Rail and panel mounting enabled

 Physical Ports
  IAP-6002-WA IAP-6002-WA+
10/100Base-T(X) Ports in RJ45 Auto MDI/MDIX 2
PoE. PD port   Present at ETH2
  Fully compliant with IEEE 802.3af   Power
  Device specifi cation
  Over load & short circuit protection
  Isolation Voltage : 1000 VDC min.
  Isolation Resistance : 108 ohms min

 

 WLAN interface
Operating Mode AP/Bridge/Repeater/AP-Client
Antenna Connector Reverse SMA
Radio Frequency Type DSSS
Modulation IEEE802.11a : OFDM with BPSK, QPSK, 16QAM, 64QAM
OFDM @ 54 Mbps, CCK @ 11/5.5 Mbps, DQPSK @ 2 Mbps, DBSK @ 1 Mbps
IEEE802.11b : CCK, DQPSK, DBPSK
IEEE802.11g : OFDM with BPSK, QPSK, 16QAM, 64QAM
Frequency Band America / FCC : 2.412~2.462 GHz (11 channels) 5.15 to 5.25 GHz (4 channels)
Europe CE / ETSI : 2.412~2.472 Ghz (13 channels) 5.15 to 5.25 GHz (4 channels)
Transmission Rate IEEE802.11b : 1/ 2/ 5.5/ 11 Mbps
IEEE802.11a/g : 6/ 9/ 12/ 18/ 24/ 36/ 48/ 54 Mbps
Transmit Power IEEE802.11a/b/g : 18dBm
Receiver Sensitivity -81dBm @ 11Mbps, PER< 8%;
-64dBm @ 54Mbps, PER< 10%
Encryption Security WEP : (64-bit ,128-bit key supported)
WPA :
WPA2 : 802.11i(WEP and AES encryption)
PSK (256-bit key pre-shared key supported)
802.1X Authentication supported
TKIP encryption
Wireless Security SSID broadcast disable

 

 LED Indicators
Power Indicator PWR 1(2)(P.O.E.) / Ready :
  Red On : Power is on and booting up.
  Green On : Power is on and functioning Normally.
10/100TX RJ45 Port Indicator Green for port Link/Act at 100Mbps. Amber for port Link/Act at 10Mbps
WLAN LEDs WLAN Link /ACT : Green : Link, Orange : Poor signal
WLAN Strength : 1<25%, 2<50%, 3<75%, 4<100%
Fault Red : Ethernet link down or power down

 

 Fault contact
Relay Relay output to carry capacity of 1A at 24VDC

 

 Power
Redundant Input Power Dual DC inputs. 12-48VDC on 6-pin terminal block
Power Consumption (Typ.) 6 Watts
Overload Current Protection Present
Reverse Polarity Protection Present on terminal block

 

 Physical Characteristic
Enclosure IP-30
Dimension (W x D x H) 52(W) x 106.1(D) x 144.3(H) mm (2.05x4.18x5.68 inch.)
Weight (g) 800 g 804 g

 

 Environmental
Storage Temperature -40 to 85C (-40 to 185F)
Operating Temperature -10 to 55C (14 to 131F)
Operating Humidity 5% to 95% Non-condensing

 

 Regulatory approvals
EMI FCC Part 15, CISPR (EN55022) class A
EMS EN61000-4-2 (ESD), EN61000-4-3 (RS), EN61000-4-4 (EFT), EN61000-4-5 (Surge), EN61000-4-6 (CS),
EN61000-4-8, EN61000-4-11
Shock IEC60068-2-27
Free Fall IEC60068-2-32
Vibration IEC60068-2-6
Safety EN60950
Warranty 3 years

 Available Model
IAP-6002-WA   Industrial 802.11 a/b/g Redundant Access Point
IAP-6002-WA+   Industrial 802.11 a/b/g Redundant Access Point with 1-port PoE PD


 RF Accessaries
WLAN RF Antenna (Outdoor Panel type)
RFA-P1-WG   Outdoor Hign-gain Panel Antenna, 2.4GHz, 12dbi max, N Female connector
RFA-P1-WA   Outdoor High-gain Panel Antenna, 5.8GHz, 14dbi max, N Female connector

WLAN RF Antenna (Omni-directional)
RFA-O1-WG   Omni-directional Hign-gain Panel Antenna, 2.4GHz, 9dbi max, SMA Male RS connector

RF Antenna Base (Magnetic)
RFB-M1-150   Magnetic WLAN RF Antenna Base, Cable length 1.5m, SMA Female RS to SMA Male RS connector
RFB-M1-1000   Magnetic WLAN RF Antenna Base, Cable length 10m, SMA Female RS to SMA Male RS connector

RF Cable
RFC-SFR-SMR-1000   Low loss RF Cable, Cable length 10m, SMA Female RS to SMA Male RS connector
RFC-NF-NM-1000   Low loss RF Cable, Cable length 10m, N Female to N Male connector
RFC-NM-SMR-150   Low loss RF Cable, Cable length 1.5m, N Male to SMA Male RS connector
RFC-NM-SMR-1000   Low loss RF Cable, Cable length 10m, N Male to SMA Male RS connector


 DIN-Rail Power Supply
DR-4512   45W DIN-Rail 12VDC/3.5A Power Supply with universal 100 to 240VAC input
DR-4524   45W DIN-Rail 24VDC/2A Power Supply with universal 100 to 240VAC input
DR-75-12   75W DIN-Rail 12VDC/6.3A Power Supply with universal 100 to 240VAC input
DR-75-24   75W DIN-Rail 24VDC/3.2A Power Supply with universal 100 to 240VAC input
DR-75-48   75W DIN-Rail 48VDC/1.6A Power Supply with universal 100 to 240VAC input
DR-120-12   120W DIN-Rail 12VDC/10A Power Supply with 100 to 12VAC / 220 to 240VAC input by switch
DR-120-24   120W DIN-Rail 24VDC/5A Power Supply with 100 to 120VAC / 220 to 240VAC input by switch
DR-120-48   120W DIN-Rail 48VDC/5A Power Supply with 100 to 120VAC / 220 to 240VAC input by switch